![dante virtual soundcard sample rate dante virtual soundcard sample rate](https://cdn.xingosoftware.com/audioxpress/images/fetch/dpr_1/https%3A%2F%2Fwww.audioxpress.com%2Fassets%2Fupload%2Fimages%2F0%2F20141219062901_AudinateDanteVirtualCardUpdateWeb.jpg)
–Please note that the number in brackets is increasing and counting the physical channels, where as the label before the brackets uses a similar labeling than on the devices or in the KLANG:app. 1 to 1, 2 to 2 etc.) you can also press the ctrl key and click on the minus checkbox between transmitter and receiver. Hover your mouse over the icon to get more information on the problem. You will notice that a blank square will turn to yellow first and then quickly to green if routing was successful.
![dante virtual soundcard sample rate dante virtual soundcard sample rate](https://s1.studyres.com/store/data/008038512_1-b68531b6befb250746b6a8bc886d6251.png)
In the screenshot this is the position of the green check mark icon. To route audio, click on the square at the crossing. Before starting to route audio streams let’s make sure that all devices are configured correctly.ĭouble click on any device in the Routing tab and navigate to Device Config to set Sampling Rate (48 kHz in this example) and Latency settings (250 microseconds in this example). Open the Dante Controller on your PC/MAC and navigate to the Routing tab.
Dante virtual soundcard sample rate how to#
Read more on how to change modes and on what mode is most suitable for your setup… – – If you are unsure about the network switch setting of KLANG:fabrik or KLANG:vier connect your computer running the Dante controller to the Dante port and set the switch configuration mode to “Switch attached Control” to start. With DVS, your computer can be routed with the Dante Controller just like any other Dante equipment. The DVS allows you to send and receive audio with your computer. If you don’t have a mixing console at your fingertips, you can also use and configure KLANG equipment with the Dante Virtual Soundcard (DVS). If you connect a Dante-enabled mixing board, make sure to also connect your PC/Mac running the Dante Controller to the network. The supported audio formats are shown below.Connect Mac/PC with Dante Virtual Soundcard or Dante-enabled mixing board to KLANG:fabrik and KLANG:quelle. Note: Changing the encoding setting will interrupt audio. Use the Encoding drop-down menu to set the required bit depth.The encoding value is the audio bit depth. Note: Applying pull-up/down places the device in a dedicated clock domain, so it will only be able to sync with other devices with the same sample rate and pull-up/down. Sample rate pull-up down allows you to adjust the sample rate to account for frame rate conversion in video. Subsequently decreasing the sample rate, however, will not restore the channel count setting to its previous value. Note: Increasing the sample rate in Dante Controller may reduce the channel count (’Audio Channels’) setting on Dante Virtual Soundcard, if the channel count setting is not supported at the new sample rate. Note: Changing the sample rate will interrupt audio. Use the Sample Rate drop-down menus to set the required sample rate and pull-up/down.To change the sample rate and sample rate pull-up/down (Windows only) for Dante Virtual Soundcard: Refer to the Dante Controller user guide for information about locking Dante devices remotely. You can lock and unlock Dante Virtual Soundcard from the control panel, or remotely using Dante Controller. In the Rename Device field, enter the new device name and click Apply.In Dante Controller, open the Device Config tab for Dante Virtual Soundcard.To change the Dante Virtual Soundcard device name: Changing the Device Nameīy default, Dante Virtual Soundcard will appear in Dante Controller with the same name as the computer on which it is installed.
![dante virtual soundcard sample rate dante virtual soundcard sample rate](https://support.multicam-systems.com/hc/article_attachments/360012207280/mceclip1.png)
See the Dante Controller user guide for more information about configuring Dante devices. Use Ctrl + D (command + D for macOS) to open the device view, and select the Dante Virtual Soundcard device from the drop-down menu.Double-click the Dante Virtual Soundcard device in the routing view, or:.In Dante Controller, open the device view for Dante Virtual Soundcard - either: Ensure Dante Virtual Soundcard is running.Connected applications may prevent new settings from taking effect. Completely quit out of any audio applications (such as DAWs) that are using Dante Virtual Soundcard.To open the Device View > Device Config tab: To change these settings, use the Device Config tab of the Device View in Dante Controller. Sample Rate (and sample rate pull-up/down in Windows).Some Dante Virtual Soundcard settings are only configurable via Dante Controller: